Installation Instructions in the following order for items listed:
- 2008 B-King Frame Sliders
- 2008 B-King Fork Sliders
2008 SUZUKI B-KING FRAME SLIDER INSTALLATION INSTRUCTIONS
NOTE: These sliders attach directly to the motor mounts of the bike and require no modifications or cutting of the body
pieces.
The right side of the bike is the side with the throttle, and the left side of the bike is the side with the clutch lever.
1. Locate the upper motor mounts in the frame of the bike; they are totally exposed on both sides of the bike.
2. Install one slider at a time- do not loosen both motor mounts at the same time.
3. Starting with the right side, loosen (counter-clockwise rotation when viewed from the side of the bike) the factory
motor mount screw and remove it from the motor mount.
4. For the right side, select the shortest of the two sliders.
5. Lightly lubricate (any type of automotive grease or oil will work) the supplied screw threads. Place the slider over the
mounting point and insert the screw through the slider and the motor mount, then turn the screw clockwise. You should
feel the threads of the screw engage the threads of the motor mount. There should be little resistance until the screw
head contacts the aluminum spacer inside the slider. DO NOT use an impact gun or an air wrench to install the
sliders.
6. If using a torque wrench, torque the screws to 38 ft lbs. If you do not have a torque wrench, use a ½”-drive ratchet
and apply moderate forces; do not use a breaker bar to tighten the screws.
7. For the left side, use the longest of the two sliders. Repeat the steps used for the right side.
For technical assistance, please contact us
To maintain the factory shine of your OES frame sliders, we recommend using an automotive wax or polish on them
regularly.
If you damage one slider in a crash or drop, you can order just the side you need on this site
- 2008 B-King Frame Sliders
- 2008 B-King Fork Sliders
2008 SUZUKI B-KING FRAME SLIDER INSTALLATION INSTRUCTIONS
NOTE: These sliders attach directly to the motor mounts of the bike and require no modifications or cutting of the body
pieces.
The right side of the bike is the side with the throttle, and the left side of the bike is the side with the clutch lever.
1. Locate the upper motor mounts in the frame of the bike; they are totally exposed on both sides of the bike.
2. Install one slider at a time- do not loosen both motor mounts at the same time.
3. Starting with the right side, loosen (counter-clockwise rotation when viewed from the side of the bike) the factory
motor mount screw and remove it from the motor mount.
4. For the right side, select the shortest of the two sliders.
5. Lightly lubricate (any type of automotive grease or oil will work) the supplied screw threads. Place the slider over the
mounting point and insert the screw through the slider and the motor mount, then turn the screw clockwise. You should
feel the threads of the screw engage the threads of the motor mount. There should be little resistance until the screw
head contacts the aluminum spacer inside the slider. DO NOT use an impact gun or an air wrench to install the
sliders.
6. If using a torque wrench, torque the screws to 38 ft lbs. If you do not have a torque wrench, use a ½”-drive ratchet
and apply moderate forces; do not use a breaker bar to tighten the screws.
7. For the left side, use the longest of the two sliders. Repeat the steps used for the right side.
For technical assistance, please contact us
To maintain the factory shine of your OES frame sliders, we recommend using an automotive wax or polish on them
regularly.
If you damage one slider in a crash or drop, you can order just the side you need on this site
2008 B-King Fork Sliders Installation Instructions
Note: This set is installed with the front axle and axle bolt in their normal operating positions.
1. Apply medium strength threadlocker compound (available here) to the left side mounting screw, which is the
shortest of the two screws in the set.
2. Install the left side axle slider (long slider) onto the shaft and lightly tighten with a 5mm hex wrench.
3. Insert slider and shaft assembly into the axle from the left side.
4. Apply medium threadlocker compound to the long screw and insert through the right side slider. While holding the
left side slider firmly in place by hand, insert the screw through the axle bolt and carefully start the right side screw into
the shaft. It may take some careful positioning of the shaft to get the threads started into the shaft.
5. Once the screw has been started and confirmed that proper thread engagement was made, lightly torque the right
side.
6. Final tighten the left side screw with light torque.
Important: Do not over tighten the left or right side screw.
For technical assistance, please contact us
Note: This set is installed with the front axle and axle bolt in their normal operating positions.
1. Apply medium strength threadlocker compound (available here) to the left side mounting screw, which is the
shortest of the two screws in the set.
2. Install the left side axle slider (long slider) onto the shaft and lightly tighten with a 5mm hex wrench.
3. Insert slider and shaft assembly into the axle from the left side.
4. Apply medium threadlocker compound to the long screw and insert through the right side slider. While holding the
left side slider firmly in place by hand, insert the screw through the axle bolt and carefully start the right side screw into
the shaft. It may take some careful positioning of the shaft to get the threads started into the shaft.
5. Once the screw has been started and confirmed that proper thread engagement was made, lightly torque the right
side.
6. Final tighten the left side screw with light torque.
Important: Do not over tighten the left or right side screw.
For technical assistance, please contact us
______________________________________________________________________________________________
