07-08 CBR600RR Frame Sliders Installation
These instructions explain the installation of OES frame sliders on the 07-08 Honda CBR600RR. The
instructions are based on the use of our special alignment tool to be used to mark the lower fairings in
preparation for cutting the frame slider half hole. The tool is not automatically included with the frame sliders
set, since different methods are used to cut the fairings by different installers.
1. Start on either side of the bike (work on one side at a time) by removing the lower side fairing.
2. Locate the forward engine mount screw. The mount is directly forward of the stator cover on the left side,
and directly forward of the clutch/timing cover on the right side.
3. Remove the factory engine mount screw (17mm socket and ratchet)
4. Install the alignment tool in place of the engine mount screw. Thread it in most of the way.
5. Install the fairing. Make sure the fairing is installed fully- installing the fairing improperly will result in a
misaligned half hole in the fairing.
6. Adjust the tool outward until it makes contact with the inside of the fairing.
7. Push inward on the fairing, directly over the point of the tool. This will make a mark on the inside of the
fairing, indicating where the fairing needs to be cut.
8. Remove the fairing
9. At the mark, drill a 1/8" or smaller pilot hole through the fairing, drilling from the inside out.
10. Use a hole saw that has a pilot drill in the center. The saw should be slightly larger (no more than 1/8")
than the frame slider diameter. When cutting, you won't be cutting a full circle- it will be a half circle since you'll
be cutting at the edge of the fairing.
11. Remove the alignment tool.
12. Lightly lubricate (any type of automotive grease or oil will work) the supplied screw threads. Install the
frame slider (both sides are the same) using a 10mm Allen socket and ratchet. If using a torque wrench,
tighten to 35 lb/ft.
13. Re-install the lower side fairing.
Repeat the steps on the opposite side.
Special Note:
* If you have a crash and damage one side, you can purchase just the side you need by contacting us or by
purchasing directly from our website.
We will be more than happy to provide customer support if needed- please contact us
These instructions explain the installation of OES frame sliders on the 07-08 Honda CBR600RR. The
instructions are based on the use of our special alignment tool to be used to mark the lower fairings in
preparation for cutting the frame slider half hole. The tool is not automatically included with the frame sliders
set, since different methods are used to cut the fairings by different installers.
1. Start on either side of the bike (work on one side at a time) by removing the lower side fairing.
2. Locate the forward engine mount screw. The mount is directly forward of the stator cover on the left side,
and directly forward of the clutch/timing cover on the right side.
3. Remove the factory engine mount screw (17mm socket and ratchet)
4. Install the alignment tool in place of the engine mount screw. Thread it in most of the way.
5. Install the fairing. Make sure the fairing is installed fully- installing the fairing improperly will result in a
misaligned half hole in the fairing.
6. Adjust the tool outward until it makes contact with the inside of the fairing.
7. Push inward on the fairing, directly over the point of the tool. This will make a mark on the inside of the
fairing, indicating where the fairing needs to be cut.
8. Remove the fairing
9. At the mark, drill a 1/8" or smaller pilot hole through the fairing, drilling from the inside out.
10. Use a hole saw that has a pilot drill in the center. The saw should be slightly larger (no more than 1/8")
than the frame slider diameter. When cutting, you won't be cutting a full circle- it will be a half circle since you'll
be cutting at the edge of the fairing.
11. Remove the alignment tool.
12. Lightly lubricate (any type of automotive grease or oil will work) the supplied screw threads. Install the
frame slider (both sides are the same) using a 10mm Allen socket and ratchet. If using a torque wrench,
tighten to 35 lb/ft.
13. Re-install the lower side fairing.
Repeat the steps on the opposite side.
Special Note:
* If you have a crash and damage one side, you can purchase just the side you need by contacting us or by
purchasing directly from our website.
We will be more than happy to provide customer support if needed- please contact us
Installation Instructions in the following order for:
- 07-08 600RR Frame Sliders
- 07-09 600RR Fork Sliders (discontinued)
- 03-09 600RR Footpeg Risers (discontinued)
- 07-08 600RR Frame Sliders
- 07-09 600RR Fork Sliders (discontinued)
- 03-09 600RR Footpeg Risers (discontinued)
Honda 03-09 CBR-600RR Footpeg Risers Installation Instructions
(discontinued part)
Tools/Items You Will Need:
8mm Allen wrench or hex driver/ratchet
5mm Allen wrench or hex driver/ratchet
Blue threadlocker compound (available here)
1. Remove the factory footpeg bracket assembly using the 8mm Allen wrench or hex driver
2. Apply a small amount of Loctite to the supplied stainless screws and attach the bracket to the frame using
the
5mm Allen wrench or hex driver.
3. Apply a small amount of Loctite to the factory screws and attach the footpeg bracket assembly to the riser
using
the 8mm Allen wrench or hex driver.
Repeat steps 1-3 on the opposite side
Caution: Do not use high alkaline based detergents to clean the brackets. Use of harsh detergents could
cause discoloration of the anodized finish of the parts.
For technical assistance please feel free to contact us
(discontinued part)
Tools/Items You Will Need:
8mm Allen wrench or hex driver/ratchet
5mm Allen wrench or hex driver/ratchet
Blue threadlocker compound (available here)
1. Remove the factory footpeg bracket assembly using the 8mm Allen wrench or hex driver
2. Apply a small amount of Loctite to the supplied stainless screws and attach the bracket to the frame using
the
5mm Allen wrench or hex driver.
3. Apply a small amount of Loctite to the factory screws and attach the footpeg bracket assembly to the riser
using
the 8mm Allen wrench or hex driver.
Repeat steps 1-3 on the opposite side
Caution: Do not use high alkaline based detergents to clean the brackets. Use of harsh detergents could
cause discoloration of the anodized finish of the parts.
For technical assistance please feel free to contact us
(Discontinued part)